Sam's Laser FAQ, Copyright © 1994-2004, Samuel M. Goldwasser, All Rights Reserved.
I may be contacted via the Sci.Electronics.Repair FAQ Email Links Page.

  • Back to Sam's Laser FAQ Table of Contents.

    Home-Built Pulsed Solid State (PSS) Laser

    Sub-Table of Contents



  • Back to Home-Built PSS Laser Sub-Table of Contents.

    Basic Home-Built PSS Laser Information

    Introduction to Home-Built PSS Laser

    Among high power lasers, the Pulsed Solid State (PSS) laser is probably the easiest to construct from components available on the surplus market. A Nd:YAG rod in decent condition (flat polished ends without damage) can be made to generate destructive amounts of pulsed energy at 1,064 nm (near-IR, quite invisible) with relatively little effort as these things go. :) Pump energy, usually from xenon flashlamps, will be needed but it may be possible for these to just be flash units from disposable cameras, appropriately remounted to efficiently couple their light into the laser rod. The HR mirror doesn't need to be nearly perfect and the OC mirror doesn't need to have that high a reflectivity (as with a HeNe laser) but with the amount of photon flux circulating inside the cavity of a pulsed laser, any absorption of light by the mirrors will result in heating and likely destruction of the coatings on the first shot, if not sooner.

    Nd:Glass is an alternative to Nd:YAG with similar lasing characteristics. Its major benefit is the availability in large sizes at reasonable cost (usually surplus from large Government laser projects). However, the thermal conductivity is much lower than YAG so repetition rates need to be much lower. (This wasn't a problem with those huge lasers that fired once an hour!)

    Ruby can also be used (it was, of course, the lasing material in the first laser) and has both advantages and disadvantages. On the plus side, the output is visible (694 nm, deep red) and pumping is a bit easier because the flash duration can be much longer. However, the threshold to get lasing is much higher for ruby (all other factors being equal) and its conversion efficiency is much lower. Being a 3 level rather than 4 level system (like YAG), the entire rod needs to be pumped or else unpumped regions will absorb any laser light which may result in an unusably high threshold and greatly reduced output.

    A variety of other laser crystals can be used but probably don't offer significant advantages unless you are interested in the particular wavelength they generate. Three common types are Erbium:YAG (Er:YAG, lases at 2,940 nm), Er:Glass (1,540 nm), and Holmium:YAG (Ho:YAG, 2,100 nm). They are likely to be less common on the surplus market than either Nd:YAG or ruby. But, due to lower popularity, may be available at attractive prices.

    The power supply for a pulsed solid state laser consists of a Pulse Forming Network (PFN), capacitor charger, and flashlamp trigger circuit. Detailed information can be found in the chapters starting with: SS Laser Power Supplies.

    However, note that like the home-built diode pumped solid state laser, constructing a PSS laser truly from scratch is way out of the question onless you are willing to do the glass work and gas filling of a custom flashlamp lamp and work for a laser crystal company to fabricate, grind, polish the rod. :) So, you may feel that a PSS laser doesn't offer enough of a challenge or reward without being able to say you did everything from the the ground up. Building one for $10 is also probably not realistic although with a bit of ingenuity, the costs can be kept quite low. I do consider a PSS laser to be worthy of home-built laser status as long as we're talking about dealing with the individual components (rod, lamp(s), mirrors, cavity reflector, power supply, etc.). You will need to decide whether just hooking up an M60 rangefinder ruby laser head or SSY1 Nd:YAG laser head to a home-built capacitor charger and PFN qualifes. :)

    Much of the information in this chapter also applies to arc lamp and halogen lamp pumped SS Nd:YAG (the material that would be most suitable) lasers. However, with the increasing popularity of high power laser diodes as pump sources, CW lamp pumped lasers are rapidly losing their appeal due to their HUGE power requirements and waste heat, and terrible efficiency. Therefore, there will be little or no specific information on these beasts.

    Home-Built PSS Laser Safety

    There are three areas of safety considerations for the home-built pulsed solid state laser: Provide proper warning signs for both the laser radiation and high voltage. Keep pets and small children out of the area and make sure everyone present is instructed as to the dangers. The use of proper laser safety goggles for the specific wavelength(s) of your laser are highly recommended.

    For more information, see the chapter: Laser Safety. Sample safety labels which can be edited for this laser can be found in the section: Laser Safety Labels and Signs.

    PSS Laser Construction References and Links

    Home-Built PSS Laser Description

    The PSS laser described below should be capable of producing output pulses of up to 1 joule or more if high quality components are used in its construction. Now, 1 J may not sound like much except that it will be generated in about 100 us representing a peak power of over 10,000 W! This will easily put holes in aluminum soda cans and possibly razor blades (a rating of 1 Gillette) in a single shot when its output is focused with a short focal length positive lens. With the addition of a Q-switch (not shown), peak powers of 100s of MEGAWATTs may be possible. In either case, it will also put holes in things you value more than soda cans and razor blades - like the back of your eyeballs - so take care! The power supply is also quite lethal.

    As noted previously, for a YAG laser, the specific sizes/ratings of the components aren't at all critical. A wide variety of designs will result in a working PSS laser, possibly with better performance than the one shown. Thus, don't restrict your search for the YAG rod, flashlamp, and optics to those shown in the diagram or described below. Matching the lengths of the rod and flashlamp will be best, but for YAG, it isn't critical. Using a 2 inch flashlamp with a 3 inch rod should still work. (With ruby, a 3-level laser, unpumped regions of the rod absorb the laser light and if a ruby rod isn't fully pumped, result in a much higher threshold or inability to lase at all). Of course with either, using a flashlamp that is too long is just wasting photons. :)

    Refer to Typical Home-Built PSS Laser Assembly for a simplified diagram of a typical laser head.

    Sources of Special Parts and Supplies for the Home-Built PSS Laser

    For capacitors and other power supply related items, see the chapter: SS Laser Power Supplies. The following deals with sources for flashlamps, laser rods, and optics - which would be the major laser surplus places and eBay. You won't find this stuff in Radio Shack or even Edmund Scientific. Buying new is probably out of the question for most of us - a typical flashlamp will go for several $100 and a small YAG rod for several $1,000.

    Flashlamps:

    The best types of flashlamps are those designed for laser pump applications. They are generally of higher quality than the type in that disposable camera flash and are constructed with materials to handle higher energy and pass the wavelengths needed for pumping laser rods. You'll also want a flashlamp with an arc length approximately equal to the length of your laser rod. This will result in highest efficiency for any laser but is particularly critical for ruby. If the lamp is too short, unpumped regions will absorb any laser light which may result in an unusably high threshold and greatly reduced output. Note that while a helical flashlamp may look 'cool', it's generally easier to deal with linear flashlamps for pumping laser rods - too much light energy is lost to reflections from the coils and out the ends of the cavity even if a perfect reflector surrounds them. And, the long discharge path means helical flashlamps will tend to have larger Ko values and thus require higher voltage to achieve the same pulse width.

    The "gold standard" for flashlamps has been EG&G (now Perkin-Elmer) but many other companies make similar lamps. (See the section: EG&G 1300 Series Linear Flashlamp Specifications.) Needless to say, these are very expensive if purchased new.

    Laser pump flashlamps can often be found at the major laser surplus places as well as on eBay. However, make sure that what is listed is actually a flashlamp and not an arc lamp - the latter won't survive for long when driven in pulsed mode! Sellers frequently don't know the difference. The only sure way to know is from the part number though high power arc lamps tend to have one pointed electrode and better coupling between the electrodes and exterior for improved heat transfer.

    For a small PSS laser, common photographic flashlamps available from major electronics distributors like DigiKey, Mouser and electronics surplus places may in fact be adequate, if not ideal. These may be suited for ruby with its long fluorescence lifetime so the pulse width can be long thus reducing stress on the flashlamp and allowing regular electrolytic capacitors to be used in the PFN. However, this is offset somewhat by the much lower threshold inherent with YAG where the flash unit from a disposable camera may be adequate to pump a 1 to 1.5 inch YAG rod.

    Laser rods:

    Ideally, what you want are never used rods with ground, polished, and AR (Anti-Reflection) or mirror coated ends. Except for the AR coatings, this is essential - you aren't going to do optical quality finishing work in your basement! If the seller doesn't explicitly say this, ask. It's possible to use rods without AR coatings. However, efficiency and stability may be slightly lower if they are not cut at the Brewster angle. Getting rods with at least one of the mirrors already on the end of the rod will certainly simplify the laser design but these are not very common.

    In particular, avoid those from eBay seller ID ninteach whose "Military Surplus" rods are probably good only to cut up for jewelry or as conversation pieces, but not for lasers. (He may also be selling the same junk under other eBay user IDs selling the same junk.) It's quite amazing what uninformed people will pay for these! $15 for a garbage rod to experiment with or as a curiosity might be reasonable. But I've seen them go for $150 or more! Some of the specific known problems with these include:

    1. Impurities/inclusions in the crystal. These result in refraction of the light inside the rod.

    2. Rough ground but not polished ends. Optical grade polishing will be costly. This isn't something you are likely to be able to do in your basement.

    3. Significant non-uniform diameter. This will result in non-uniform pump energy in the interior.

    Aside from the tint of the material, a high quality rod with polished and AR coated ends should just about disappear when viewed lengthwise. The interior should be crystal-clear with absolutely no distortion.

    Realistically, most of the rods available at reasonable cost for home-built PSS lasers are going to be used and in varying states of health but most should be adequate if in good physical condition. Yes, there is such a thing as a depleted rod (see below, and it has nothing to do with nuclear reactors!) but rods pulled from a commercial lasers when their output energy/power falls below spec'd values should still have a lot of life left.

    Laser surplus places like Meredith Instruments and others may carry ruby, Nd:YAG, and sometimes, other strange laser rods. Since these are usually not continuously stocked items but come and go, checking back from time-to-time will be desirable. In any case, I'd recommend sticking with the common lasing materials even if you find something else cheap. YAG is easiest to make lase but its output is invisible. Ruby produces visible output but has a higher threshold. Optics for both of these are likely to be more readily available than for others. A bargain rod isn't a bargain if everything else costs more!

    And if you're determined to have the biggest laser on your block, check out Neodymium Glass. They must have gotten surplus optics from the older Livermore lasers.

    Laser rods turn up quite frequently on eBay, both pulls from equipment and never used (NOS, New Old Stock). Monitoring auctions with the words "laser", and "YAG" or "ruby" (as desired) shouldn't take too much time.

    (From: Steve J. Quest (Squest@cris.com).)

    "The last Nd:YAG rod we bought new, we paid $3,000. It was a 5 mm x 72 mm rod. The rods MWK sells may possibly be unusable, depleted rods, where all the neodymium has migrated. Depleted rods do work, but they don't work the best, but are OK for hobby projects I suspect. Probably they were RFE (Removed From Equipment) usually from the laser marking/engraving industry (the date codes on pop cans, etc.) You'll have to check with MWK to find out the source for the rods."

    Optics:

    The HR can be either a totally reflecting high energy dielectric mirror or a roof prism or corner reflector, AR coated for the laser wavelength if possible. A high quality first surface aluminized mirror might survive for a few shots or more but with the high intra-cavity power of a PSS laser, possibly not for long. And, probably not at all if Q-switched!

    The OC mirror really needs to be one designed for PSS laser. Without a Q-switch, figure something like 70 percent reflectivity at the lasing wavelength. With a Q-switch, it can be as low as 30 percent. I'd suggest avoiding "resonant" type mirrors in favor of high energy dielectric types. While resonant optics have no coatings to be damaged, their internal optical element spacing and alignment are absolutely critical (if disassembled for any reason, will likely be ruined). And, their condition or even effective reflectivity can't easily be determined. The reflectivity is also likely to be too low for useful operation without a Q-switch. Although the original ruby laser, circa 1960, used an aluminum output mirror with a hole in the middle, this is probably not a great idea (but it wouldn't hurt to try!).

    Laser surplus places and eBay are the likely sources unless you are willing to pay big $$$ for them.

    (From: Chris Leubner (cdleubner@ameritech.net).)

    I have found that some of the IR attenuators out of very old color video cameras work as a half way descent OC for those ruby lasers, You need the type that are made of clear glass with a reddish mirror coating, the blue ones will not work.



  • Back to Solid State Lasers Sub-Table of Contents.

    Other Examples of Home-Built PSS Lasers

    Chris's High Energy Dual Flashlamp Pumped Nd:YAG Laser

    (From: Chris Chagaris (pyro@grolen.com).)

    This is an experimental dual flashlamp-pumped solid-state laser built quite inexpensively to be used for educational demonstrations as well as the experimental testing of various components to determine their effect on laser performance. See: Chris's High Energy Dual Flashlamp Pumped Nd:YAG Laser (Diagram) for the basic layout of the system. The completed unit (with cavity cover removed) is shown in Chris's High Energy Dual Flashlamp Pumped Nd:YAG Laser (Photo) It really does look just like the diagram! :)

    I did get my first coherent photons from it just the other evening. I am in need of some good YAG resonant optics to maximize this laser's performance, as efficiency is not very high right now. The best I've done so far has been a 0.97 joule output pulse with an input of 200 joules. This was read with my questionably calibrated Ophir laser power meter. I will try to get some pictures of this laser soon.

    Here are the general specifications:

    I do plan on the passive Q-switching of this laser in the future. My 'ever cheap plan' is to construct a small quartz dye chamber placed near, or as a part of, the high reflector and employ an organic dye suitable for YAG Q-switching within this cell.



  • Back to Home-Built PSS Laser Sub-Table of Contents.

    Additional Information on Home-Built PSS Lasers

    Home-Built PSS Laser Alignment and Optimization

    Initial alignment is best done with a low power HeNe laser reflecting from the relevant surfaces of the HR and OC mirrors back to its output aperture. Although alignment isn't nearly as difficult or critical for this short wide bore laser as for a long narrow bore HeNe laser, the multiple weak reflections from all of the nearly transparent (for visible wavelengths) surfaces can be confusing (since the actual mirror reflections may not appear significantly different at the red HeNe wavelength than uncoated surfaces or AR coated surface at IR wavelengths). The trick is to identify the relevant pair! Since all surfaces are planar, sharpness/fuzzyness of the spot can't be used as an identifier. To simplify things, assuming the rod has planar ends that are perpendicular to the rod axis, it can be removed for initial alignment eliminating two confusing surfaces. And, putting a drop of water, alcohol, or a strategically placed fingerprint :) on the back of the HR will scramble any reflection from its rear surface and remove it from consideration.

    Detecting the beam and optimizing alignment can be done by checking the beam profile with Zapit(tm) paper, thermal fax or printer paper, a photocopy of a black original, other black paper, or black electrical tape, and maximizing hole-blasting effectiveness. ;-)

    Converting a Lamp Pumped IR YAG Laser to Green?

    Multiwatt Halogen, arc lamp, or flashlamp pumped solid state lasers are readily available at reasonable prices from laser surplus outfits, eBay, and elsewhere. What about adding a KTP (or other SHG crystal) and getting them to output nice 532 nm green? (Similar comments apply to higher harmonics but the difficulty level increases significantly.) While this would appear at first to be an easy project, the realities may be quite different. There are a number of issues all relating to peak power density available and shape of the beam inside the crystal. Maximum harmonic power will be generated when a narrow polarized collimated beam is properly phase matched to the KTP (Type-II critical phase matching). If the original laser isn't polarized (e.g., Nd:YAG without Brewster angled rod ends), adding a polarizing element will significantly increase performance. Since harmonic generation is a non-linear process, it is desirable to maximize power density so long as it is safely less than the damage threshold of the KTP.

    Lamp pumped SS lasers often use flat-flat resonators to prevent hot spots inside the YAG rod. The intra and output beams both have a large diameter (almost equal to the rod diameter) and are massively multi (transverse) mode. Just inserting a KTP crystal into the beam (inside or outside the cavity) without taking into these factors and peak power density of the beam will likely result in either poor performance or damage to the KTP. With the multimode beam, it isn't sufficient to just consider the average power density in the beam cross-section - peak power in the hot spots due to the sub-beams must be taken into account.

    In short, this may be possible but don't expect miracles, at least not unless the conversion is carefully designed and executed.



  • Back to Sam's Laser FAQ Table of Contents.
  • Back to Home-Built PSS Laser Sub-Table of Contents.
  • Forward to Home-Built Diode Pumped Solid State (DPSS) Laser.


    Sam's Laser FAQ, Copyright © 1994-2004, Samuel M. Goldwasser, All Rights Reserved.
    I may be contacted via the Sci.Electronics.Repair FAQ Email Links Page.